| General | NX-1700H | NX-1800H | |
|---|---|---|---|
| Frequency Range | 136-174 MHz | 400-470 MHz | |
| Max. Channels Per Radio | 260 | ||
| Number of Zones | 128 | ||
| Max. Channels per Zone | 250 | ||
| Channel Spacing | Analog | 12.5/25 kHz | |
| Digital | 6.25/12.5 kHz | ||
| Power Supply | 13.6 V DC ±15% | ||
| Current Drain | Standby | 0.45 A | |
| RX | 2.4 A | ||
| TX | 13 A | ||
| Operating Temperature | -22ºF to +140ºF (-30ºC to +60ºC) | ||
| Frequency Stability | ±0.5 ppm | ||
| Dimensions | (W x H x D) Projections Not Included | ||
| 6.34 x 1.69 x 6.62 in. | |||
| (161 x 43 x 168.2 mm.) | |||
| Weight Radio | 2.67 lbs (1.21 kg) | ||
| FCC ID | Type 1 | K44517000 | K44517100 (Pending) |
| Type 2 | |||
| FCC ID | Type 1 | 282F-517000 | 282F-517100 (Pending) |
| Type 2 | |||
| IC Certification | 282F-501001 | 282F-501102 | |
| Receiver | NX-1700H | NX-1800H | |
| Sensitivity | NXDN® 6.25 kHz Digital (3% BER) | 0.18 μV | |
| NXDN®12.5 kHz Digital (3% BER) | 0.22 μV | ||
| DMR Digital 12 kHz (5% BER) | 0.18 µV | ||
| Analog 12 kHz (12dB SINAD) | 0.20 μV | ||
| Analog 25 kHz (12dB SINAD) | 0.24 μV | ||
| Sensitivity | Analog @ 12.5kHz | 65 dB | |
| Analog @ 25kHz | 81 dB | ||
| Intermodulation | 73 dB | ||
| Spurious Rejection | 75 dB | ||
| Audio Distortion | 3% | ||
| Audio Output Power | 6 W/ 4 W 4 Ω | ||
| Transmitter | NX-1700H | NX-1800H | |
| RF Power Output | 50 W / 25 W / 5 W | 45 W / 25 W / 5 W | |
| Spurious Emission | -73 dB | -75 dB | |
| FM Hum & Noise | Analog @ 12.5kHz | 40 dB | |
| Analog @ 25kHz | 50 dB | ||
| Audio Distortion | 3% | ||
| Emission Designator | 16K0F3E, 11K0F3E, 8K30F1E, 8K30F1D, 8K30F7W, 4K00F1E, 4K00F1D, 4K00F7W, 4K00F2D, 7K60FXD, 7K60FXW, 7K60FXE, 7K60F1E, 7K60F1D, 7K60F1W |
||
Analog measurements made per TIA603. Specifications are measured according to applicable standards.
Specifications shown are typical and subject to change without notice, due to advancements in technology.
NXDN® is a registered trademark of JVCKENWOOD Corporation and Icom Inc.
NEXEDGE® & FleetSync® are a registered trademarks of JVCKENWOOD Corporation.
All other trademarks are the property of their respective holders.
| MIL Standard | MIL 810C Methods/Procedures | MIL 810D Methods/Procedures | MIL 810E Methods/Procedures | MIL 810F Methods/Procedures | MIL 810G Methods/Procedures | MIL 810H Methods/Procedures |
|---|---|---|---|---|---|---|
| Low Pressure | 500.1/Procedure I | 500.2/Procedure I, II | 500.3/Procedure I, II | 500.4/Procedure I, II | 500.5/Procedure I, II | 500.6/Procedure I, II |
| High Temperature | 501.1/Procedure I, II | 501.2/Procedure I, II | 501.3/Procedure I, II | 501.4/Procedure I, II | 501.5/Procedure I, II | 501.7/Procedure I, II |
| Low Temperature | 502.1/Procedure I | 502.2/Procedure I, II | 502.3/Procedure I, II | 502.4/Procedure I, II | 502.5/Procedure I, II | 502.7/Procedure I, II |
| Temperature Shock | 503.1/Procedure I | 503.2/Procedure I | 503.3/Procedure I | 503.4/Procedure I, II | 503.5/Procedure I | 503.7/Procedure I |
| Solar Radiation | 505.1/Procedure I | 505.2/Procedure I | 505.3/Procedure I | 505.4/Procedure I | 505.5/Procedure I | 505.7/Procedure I |
| Rain* | 506.1/Procedure I, II | 506.2/Procedure I, II | 506.3/Procedure I, II | 506.4/Procedure I, III | 506.5/Procedure I, III | 506.6/Procedure I, III |
| Humidity | 507.1/Procedure I, II | 507.2/Procedure II, III | 507.3/Procedure II, III | 507.4 | 507.5/Prcedure II | 507.6/Prcedure II |
| Salt Fog | 509.1/Procedure I | 509.2/Procedure I | 509.3/Procedure I | 509.4 | 509.5 | 509.7 |
| Dust | 510.1/Procedure I | 510.2/Procedure I | 510.3/Procedure I | 510.4/Procedure I, III | 510.5/Procedure I | 510.7/Procedure I |
| Vibration | 514.2/Procedure VIII, X | 514.3/Procedure I | 514.4/Procedure I | 514.5/Procedure I | 514.6/Procedure I | 514.8/Procedure I |
| Shock | 516.2/Procedure I, II, III, V | 516.3/Procedure I, IV, V | 516.4/Procedure I, IV, V | 516.5/Procedure I, IV, V | 516.6/Procedure I, IV, V | 516.8/Procedure I, IV, V, VI |
| International Protection Standard | ||||||
| Dust & Water Protection*1 | IP54 (per IEC60529) | *1 All interfaces must be fully sealed with appropriate covers or by designated genuine accessories | ||||
